- #Tlw transmission line program for windows software#
- #Tlw transmission line program for windows code#
- #Tlw transmission line program for windows series#
And there's no way to know without doing more rigorous calculations. The disadvantage of the ARRL formula is that the results may or may not be particularly accurate. And they all copied that script directly or indirectly from the original.
#Tlw transmission line program for windows code#
That's why so many online calculators all look the same they all use the same script code in the html of the web page. The advantage of using this formula is that it is simple and thus easy to implement using JavaScript. The ProblemMost of the online calculators use the ARRL's "Additional Loss Due to SWR" formula, shown (with minor edits) below. Online coax loss calculators that use SWR as one of the inputs certainly are convenient but can you trust the results?Alternative tools which are much more accurate are readily available. Think Twice Before Using a Web-Based Line Loss Calculator LA-4 tip: This connector provides additional 4 input channels on SD4.1 probe to increase the number of input channels."Additional Loss Due to SWR" is in Quotes for a Reason When installing the connector, you must watch out for correct sides.ī. Top/Bottom labels are marked on the cable. The front end tip can be replaced with standard SD4.1-tip or uSD4.1-tip according to his or her need for measurement. The SD 4.0 pod can only be installed in slot B and can be used only with SD 4.1-tip. LA-4 tip: This connector provides additional 4 input channels on SD3.0 probe to increase the number of input channels.Īvailable only for BusFinder series. eMMC-tip: The eMMC socket tip is used to connect with SD 3.0 tip. SD 3.0 pod can only be installed in slot B. If you need to use voltage detection, please connect A0 pin to form an analog signal input.Īvailable only for BusFinder series.
NAN-tip: This is a pin with voltage detection function. LA08/09 tip: This is a general signal input channel, for connecting NAND Flash pin to be measure.ī. NAND Flash pod can only be installed in slot B. NAND Flash Probe (Optional) Available only for BusFinder series. Please be noted that the wire length should be as short as possible to maintain good signal quality. eMMC welding tip: This can be used for welding wire jumping. eMMC socket tip: This is a 2.54 mm pin header.
#Tlw transmission line program for windows software#
You can use the software to redefine the pin. Please refer to Appendix 1- Instruction for eMMC for the pin definition. LA-4 connector: This connector provides additional 4 input channels on eMMC probe to increase the number of input channels. If you need to use voltage detection, please connect A0 pin to form an analog signal input.ī. When installing the connector, you must watch out for correct sides. eMMC cable: The front end tip can be replaced by eMMC socket tip or welding tip according to his or her need for measurement. The eMMC pod can only be installed in slot B. It has 4 LA tips, each of which has 8 signal input channels and each pair of which is equipped with an external clock input (CK0 & CK1), located at the channels labeled as LA09-tip.Īvailable only for BusFinder series. Pull out: Use two fingers to simultaneously press the two connecting rods inside the slot, respectively, and the pod will pop out. Push the pod evenly into the slot until you hear the sound of click. Trigger-in jack Trigger-out jack Reference clock-in jack Reference clock-out jack Probe Installations Push in: Hold the pod to face the slot of the master unit. Red light: A long red or flashing light is displayed while the device is busy.ĭC 12V power jack USB 3.0 Type B transmission line jack for connection with the computer. Green light: Green light is on only when power and USB cables are properly connected. Slot (Socket A) Slot (Socket B) SD 4.0 data transmission socket, this USB 3.0 Type A socket is used to connect with SD 4.1-tip through the USB 3.0 cable (75cm). 73Īppearance and Functions of the Master Main Device 70 SD4.0 (uSD4.0) Probe.72 Appendix 2 Tuning settings. 63 Appendix 1 Probe Sizes and Pin Definitions. 44 Stack Oscilloscope.47 Advanced Capture Setting. 25 Statistics window.26 Hide Items window.26 Stack Oscilloscope.27 Cursor. Protocol Settings.14 Operating mode and memory setting. 11 Chapter 2 Function list and operation.13 4 Hardware Installation.4Īppearance and Functions of the Master Main Device.
#Tlw transmission line program for windows series#
LA3000 Series 2 in 1 Analyzer (Protocol + Logic)Ĭhapter 1 Installation and Setting. File Info : application/pdf, 75 Pages, 4.45MB Document Document Acute BusFinder-LA3K Manual-v1588087582477 BusFinder Series.
0 kommentar(er)
